Roof Flashing Repair in Biloxi, MS

Most roof leaks do not start in the middle of the roof — they start at the flashing. We repair and replace the metal details that waterproof every chimney, valley, vent and wall junction on Biloxi roofs.

Serving Biloxi, MS · ZIPs 39530–39535 · Requests accepted 24/7

Home › Services › Roof Flashing Repair in Biloxi, MS

Roof flashing is the metalwork that seals the joints of a roof — where shingles meet chimneys, walls, vents, skylights and each other in valleys. Flashing repair means fixing or replacing those pieces when they corrode, lift, crack or were installed wrongly. In Biloxi's salt air and driving rain, flashing is statistically the most likely source of any roof leak.

What are the signs you need roof flashing repair?

Suspect flashing when you see:

  • Leaks beside a chimney, wall or skylight — water entering exactly at a junction
  • Rusted, holed or paper-thin metal in valleys or at roof edges
  • Flashing that has lifted, bent or pulled away from the wall or chimney it should seal
  • Cracked tar or caulk patches around penetrations — old surface fixes that have failed
  • Stains on ceilings below valleys after heavy rain, when valley volume overwhelms worn metal
  • Drip edge missing or rotted fascia at the roof's lower edges

What causes it?

Flashing fails by corrosion (salt air eats galvanised metal, fastest near the Sound), by movement (houses and roofs expand differently, working step flashing loose), by storm damage, and by original shortcuts — face-nailed flashing, sealant used instead of proper counter-flashing, or tar patches that were only ever temporary. Because flashing sits at every interruption in the roof, it has the hardest job and the shortest natural life of any roof component.

How is it repaired?

Proper flashing repair is joinery, not caulking. Step flashing at walls is woven piece-by-piece with the shingle courses; chimneys get counter-flashing cut into the mortar joint, not glued to the brick; valleys are re-lined with sound metal or a proper membrane-and-metal system; vent flashing is replaced with a new boot or metal flashing matched to the roof type. Sealant has a supporting role only. Where corrosion is the cause, we use metals suited to coastal exposure so the repair outlasts the original.

Our Repair Process

Locate the failing joint

The leak's position inside points to the junction above it; we confirm which flashing piece has failed.

Written estimate

Which flashing, what replacement approach, and the price — in writing.

Strip & replace

Shingles around the joint are lifted or removed as needed, old flashing taken out, new flashing installed in correct sequence.

Re-cover & seal

Roofing is reinstated over the new flashing and the joint is checked — water-tested for leak work where practical.

Roof repair in Biloxi's climate

If Biloxi roofs have an Achilles heel, this is it. The combination of salt corrosion, extreme rain volume in valleys, and wind-driven rain at wall junctions means flashing here works harder and dies younger than inland. Older Biloxi homes — especially in East Biloxi — often have flashing that was marginal when installed and is now simply worn out. A useful rule: if a leak is anywhere near a chimney, wall, vent or valley, price the flashing repair first — it is the cause more often than everything else combined. Start with leak repair if the entry point is not yet diagnosed.

Frequently Asked Questions

Can flashing just be re-sealed with caulk or tar?

As a very short-term emergency measure, sometimes — but sealant on a failed joint is not a repair. It cracks within a season or two in Biloxi heat, and can trap water against the joint meanwhile. Correct replacement of the metal is the durable fix.

How much does flashing repair cost?

Typical flashing repairs run $300–$1,000 depending on the joint: a vent flashing is at the low end, a full chimney re-flash or long valley higher. Your estimate follows inspection.

What is the difference between step flashing and counter-flashing?

Step flashing is the series of small metal pieces woven with shingles where a roof meets a wall. Counter-flashing is the piece that caps it from the wall or chimney side, ideally set into a mortar joint. Chimneys and walls usually need both working together.

Why does my valley leak only in heavy rain?

Valleys concentrate the water from two roof slopes into one channel. Worn, narrow or debris-filled valley metal copes with light rain but is overwhelmed in a Biloxi downpour — the water rides up under the shingle edges.

Is flashing covered when shingles are repaired?

We always inspect the flashing adjoining any shingle repair. Replacing shingles over dead flashing wastes the shingle work, so if the flashing is at end of life we will show you and price it in the same estimate.

Related Services & Guides

Roof Leak Repair

Diagnosis first: find the exact entry point.

Learn more →

Shingle Roof Repair

Flashing and shingles are repaired together at junctions.

Learn more →

Metal Roof Repair

Flashing and trim on metal roof systems.

Learn more →

Leak at a Chimney, Vent or Valley?

That is flashing until proven otherwise. Request a callback and we will inspect the joint and price the proper repair.

Request a Callback